1045 plate impact strength
- Xicheng Science & Technology Building High-tech Development Zone, Zhengzhou, China
- [email protected]
- Online Chating
Key-Point: AISI 1045 provides high tensile strength and hardness but is still very machine friendly. This makes it very useful in applications which require impact and wear resistance. It can be machined and welded in both the normalized or hot rolled states but not in through hardened state.
1045 plate is a Chemistry plate, meeting the chemistry make-up listed below. The 10 designates a basic plain carbon steel and 45 designates the approximate carbon content. Like the 1020 specification, the 1045 steel specification is included in the ASTM 830 family of specifications.
AISI 1045 steel is a medium tensile steel supplied in a black hot-rolled or normalized condition. It has a tensile strength of 570 - 700 MPa and Brinell hardness ranging between 170 and 210.
1045 can be supplied as steel plate/ sheet, round steel bar, steel tube/pipe, steel stripe, steel billet, steel ingot, steel wire rods. electroslag, forged ring/ block,etc. Join Supplier: [email protected]
ASTM A830 AISI 1045 A structural quality, medium-carbon steel plate produced to a chemical composition requirement. Applications include processing industries, gear production, and mining equipment. This grade is produced with.43-.50 carbon and.60-.90 manganese content.
With higher carbon content and higher tensile strength, 1045 is a stronger steel than 1018. However, because it has a higher carbon content, it is not as easy to weld.
ASTM A830-1045 Steel Plate High-Carbon A830-C1045 steel plate is of structural quality grade plate. C1045 provides greater strength and hardness levels. These plates are usually supplied in the as-rolled (hot-rolled) condition.
Medium Tensile Carbon Steel Bar 1045 Typical Mechanical Properties in Heat Treated Condition After quenching and tempering Atlas 1045 achieves typically the following mechanical properties. Diameter (mm) Tensile Strength (MPa) 0.2% Proof Stress (MPa) Elongation (% ) Reduction of Area (% ) Impact Charpy (J)
1045 is a medium tensile low hardenability carbon steel generally supplied in the black hot rolled or occasionally in the normalised condition, with a typical tensile strength range 570 - 700 Mpa and Brinell hardness range 170 - 210 in either condition.Characterised by fairly good strength and impact properties, plus good machinability and reasonable weldability in the hot rolled or normalised condition.
Typical tensile strength ranges from 114,000 PSI (Annealed Condition) up to 156,000 PSI (Pre-Hard, Quench and Tempered Condition). AISI 4140 and 4150 steels offer a high resistance to fatigue, improved toughness, impact resistance, and torsional strength. Not all AISI 4140 and 4150 materials are made to the same standards.
AISI 1045 Carbon steel plate is characterized by good weldability and good machinability.AISI 1045 Carbon steel plate is a medium tensile steel supplied in the black hot rolled or normalized condition. It has a tensile strength of 600 MPa and brinell hardness ranging between 170 and 210.
With its higher carbon content and increased tensile strength, 1045 is a much stronger steel than 1018, which is why it is so often used in applications that require more strength than 1018 offers, such as in transmission parts.
Can be hammer forged. 1045 can be used where greater strength is required than can be obtained from the lower carbon steels. It responds to heat treatment, and a wide range of properties can be obtained. In thicker sections, partial hardening increases strength substantially, and flame or induction hardening produces a high surface hardness.
AISI 1045 Steel, cold drawn, high temperature stress relieved, 50-75 mm (2-3 in) round Categories: Metal; Ferrous Metal; Carbon Steel; AISI 1000 Series Steel; Medium Carbon Steel. Material Notes: Respond to heat treatment, and flame and induction hardening, but not recommended for carburizing or cyaniding.
Increased toughness and fatigue resistance compared to low carbon and 1045 plate. Retains high strength and wearability at high temperatures. High impact and wear properties retained at weld joints. Physical Properties. Tensile Strength 200,000 PSI. Yield Strength 160,000 PSI. Elongation in 2 14.4%. Reduction of Area 55%
C1045 hot roll plate is a silicon killed medium carbon steel. In the as-rolled condition, higher carbon content imparts increased strength over low carbon steels, such as 1018. 1045 hot roll plate is often stress relieved, normalized, or annealed after burning shapes to size to allow for easier machining.
AISI 1045 Steel is medium tensile steel supplied in the black hot rolled or normalized condition. It exhibits good weldability, good machinability, and high strength and impact properties to be used in various industrial applications. AISI 1045 steel has a low through-hardening capability that recommended for tempering and through-hardening.
Carbon 1045 is a higher strength alternative to 1018, as a result of the higher carbon content. It is the most popular medium carbon steel. It is very popular for shafts and gears. It has moderate ductility and weldability.
AISI 1045 steel is characterized by good weldability, good machinability, and high strength and impact properties in either the normalized or hot rolled condition. AISI 1045 steel has a low through-hardening capability with only sections of size around 60 mm is recommended as suitable for tempering and through-hardening. However, it can be , 1045 plate impact strength
Here is the trouble: I have a project I am working on that calls out for the following: CAN/CSA G40.21 Grade 300W OR AISI 1045 in the Normalized Condition. Needs to conform to min yield of 350MPa and tensile of 480MPa. 15% min elongation and cat. 3 Charpy Impact Testing with Min. absorbed energy of 27 Joules.
1045 is used extensively by all industry sectors for applications requiring more strength and wear resistance than the low carbon mild steels can provide and the higher strength of the low alloy high tensile steels is not necessary, plus those applications requiring flame or induction hardening.
MEDIUM TENSILE STEEL AISI 1045 AISI 1045 Medium Carbon, Medium Tensile Steel, supplied black as rolled, black as forged or normalised and bright drawn or smooth turned, offering good strength, toughness and wear resistance. Will through harden in sections up to 63mm with a tensile strength of 620 - 850 MPa. TYPICAL APPLICATIONS:
1045 flat bar stock from Capital Steel & Wire. Orders of 1045 steel flat bars can be customized and cut to any specified length. Our staff works with your business to ensure that your order exactly meets the needs of your application.
C1045 is a silicon killed medium carbon steel. Higher carbon content imparts increased strength over low carbon steels, such as C1018. Response to heat treatment is excellent, and the resultant mechanical properties can be obtained to permit wide usage in the production of machinery parts and shafts.
19% minimum in 2 (for plate 24 and wider) ASTM A633 GR E. A normalized high strength low alloy steel plate for construction. This product is suited for service at low ambient temperatures of -50oF (-45oC) and higher when notch toughness better than that expected in an As-rolled material of a comparable strength level is desired.
1045 steel round bars are special turned, ground, and polished steel designed for applications calling for a steel superior to cold rolled or hot rolled bars, but at an economical price. 1045 round bars are produced to exacting specifications to assure close tolerances in diameter, straightness and concentricity.
It also includes a steel's tension strength and yield strength. The tensile strength of AR400, often referred to as the ultimate strength, has been measured at about 200 kilograms per square inch, far more than commercial steels like American Iron and Steel Institute 1045 which has a measured tensile strength of only 90 ksi.
1040, 1045 (HR,CF) - Used when greater strength and hardness is desired in the as rolled condition. Good for hammer forge processes. Uses include gears, shafts, axles, bolts sand studs. 1040 is a medium-carbon steel composed of 0.37 to 0.44 percent carbon, 0.6 to 0.9 percent manganese, a maximum of 0.04 percent phosphorus and a maximum of 0.05 sulphur.
A572 grade 50 steel plate is a high-strength, low-alloy plate, specified for bridges, higher strength structural duties, and light pressure vessel requirements. Recommended for riveted, bolted, or welded structures, such as Gussets and Bridge Plates, when intended for construction of bridges. At 50ksi, a higher strength steel than A36.
All-purpose medium carbon steel with intermediate strength, good ductility and weldability. Application in low-stress engineering applications. Atlas 1045: Carbon steel for low to medium stress mechanical and automotive components. Can be heat treated by hardening and tempering (recommended for small and medium sections only) and surface-hardened.
1045 plate impact strength chart impact strength gym el paso texas 1045 plate impact strength test impact strength calculation 1045 plate impact strength calculator impact strength unit 1045 plate impact strength training impact strength test